Galvanized. According to European Standard EN 1065, class E. Admissible load capacity 30 kN. Higher load capacities are permitted when used with MEVA formwork (see the MevaDec Technical Instruction Manual).

Combination of steel inner tube and aluminium outer tube with T-groove to attach reinforcing frames. The SAS quick lowering system allows the stress in the prop to be released with one strike of a hammer. After stripping the prop automatically resets and locks in the original position. According to the European Standard EN 1065 the load capacity is as follows when used as a single prop: MEP 300 with SAS – 40 kN at any extension; MEP 450 with SAS – 20 kN at any assembly position (or 30 kN when the inner tube is at the bottom). Higher load capacities are permitted when used with MEVA formwork (see the MevaDec Technical Instruction Manual).

Galvanized. According to the European Standard EN 1065 class D the admissible load capacity is 20 kN at any extension. Higher load capacities are permitted when used with MEVA formwork (see the MevaDec Technical Instruction Manual).

Galvanized. The forked prop head can be used as a support instead of a drop head at the beginning or end of a primary beam row. The forked prop head 20 is applied with formwork girders H20 and.

Galvanized. Is used to attach MD drop heads, MD prop heads of forked prop heads, etc. Pin 14/90 is used for steel tube props up to Ø 63 mm. Pin 14/135 is used with the aluminium profile of MEP props and MEP extension pieces.

Galvanized auxiliary to stabilize props with Ø 48 to 80 mm. The turnable legs allow the tripod to be used in rooms, along walls or in corners. The tripod can be attached to the aluminium profile of the MEP props with the MD safety claw.

Are used to attach MD drop heads and MD prop heads to the MD/ME props.

Three-layer plywood forming face, 21 mm thick, with resistant coating on both sides. Good pore structure of the concrete due to absorbent surface. Alternative: alkus all-plastic facing.

Not shown. Multi-layer plywood forming face, 21 mm thick, with film-coating on both sides and edge protection.

Robust multi-purpose girder for the most different tasks. While the girder itself does not weigh much, it has a high load-bearing capacity (approved by building authorities). Admissible load: Q = 11 kN, M = 5 kNm.

Galvanized. Is used to connect wooden H20 girders to each other. The wedge locks the girdes into place and releases them.

Galvanized. Is plugged into the MD support for panel or beam.

Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.

Galvanized. Permits attachment of a guard-railing post at the MD panels and is used to form a stop end at the edge of the slab.

Galvanized. Permits attachment of a guard-railing post at primary and secondary beams and is used to form a stop end at the edge of the slab with primary and secondary beams.

Coated. Is used as side railing at the slab edge and can be clamped to all kinds of beams or concrete slabs. Railing clamp 100: height 100 cm, clamping length 45 cm Railing clamp 140: height 140 cm, clamping length 50 cm.

Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48.

Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at any angle required.

Steel, painted. Sturdy steel mesh with reinforced edges and closed steel sheet to prevent small items from falling down. The safety mesh serves as railing, sheet and mesh. 500 kg impact protection. Meets the requirements as defined by European standard EN 133374, classes A, B and C.

Steel, painted. Height extension for safety mesh MFS. 500 kg impact protection. Meets the requirements as defined by European standard EN 133374, classes A, B and C.

Steel, galvanized. Connects safety meshes MFS at angles from 76° to 284°. Can be attached anywhere at the safety mesh.

Steel, galvanized. Is used to form slab ends for slabs up to 60 cm thick.